A-6 Automotive Electical

1. Log-in and go to www.cte-auto.net
2. Check Aeries for assignments (Resources Tab)
3. Select and print out appropriate NATEF Task Sheet
4. Have work-group check with instructor as to vehicle assignment
5. Have shop foreman log your group into daily work log
6. Shop foreman will issue keys and tools needed for job
7. Procede to vehicle and complete assignment
8. Check tools, keys back in to shop foreman when job is complete
(minimum of 5 minutes prior to ending of period)
9. Have instructor review and sign task sheets

No changes to this procedure
without instructor approval!

 

 


NATEF Task Area A6

Electrical Curriculum

Course Outline
.Course Syllabus

NATEF Task List

Repair Order for NATEF Task

 

 

Module 1 - Electrical Theory
Electrical On-Line Assignments
  Chapter 17 - Electrical Principles PPT
Worksheet
Quiz
Chapter 18 - Circuit Types and Ohm’s Law PPT
Worksheet
 
Chapter 19 - Electric and Electronic Components PPT
Worksheet
 
Chapter 20 - Electrical Tools and Test Equipment PPT
Worksheet
 
Chapter 21 - Wiring Diagrams and Wiring Repairs PPT
Worksheet
 
Chapter 22 - Basic Electrical Tests PPT
Worksheet
 
Soldering Lab
  Soldering Soldering Video mp4
Soldering Video flv
LAB - Soldering

Module 2

A6 - Batteries
Starting & Charging Systems Worksheets
  DVOM Worksheet PPT
View
Quiz
 
  Resistor Worksheet Power Point
Chart
View & Print
 
Chapter 28 - 12-Volt and H5 Battery Technology PPT
Worksheet
Quiz
Chapter 29 - 12-Volt and HV Battery Service PPT
Worksheet
Group Lab
  Electrical Circuit Sequenced Group Labs Class Activity
  Lemon - Potato Battery Lab Video
Lemon Battery Page
Voltage Potential Chart
Lemon Battery Worksheet
Module 3
  Color Coding Schematics Worksheets Instructor-led Activities
  Schematic Symbols Worksheet PPT
View & Print Worksheet
Take Quiz
  Circuit Control Devices PDF
View & Print Worksheet
Quiz
  Conductors, Insulators, and Semi-Conductors PPT
Worksheet
Take Quiz
 
    PPT
  Color Coding Schematics #A View & Print
  Color Coding Schematics #B View & Print
  Color Coding Schematics #C View & Print
  Color Coding Schematics #D View & Print
     
Circuit Simulator Lab
  DC Wiring Circuit Construction Simulator
(Simple Circuit Simulator)
View & Print Sign-off Sheet
PPT
Simulator
 
Simple Circuits Lab
  Simple Circuit Building Practice - Worksheet 1 PPT
View & Print
  Simple Circuit Building Practice - Worksheet 2 PPT
View & Print
  Simple Circuit Building Practice - Worksheet 3 PPT
View & Print
  Simple Circuit Building Practice - Worksheet 4 PPT
View & Print
  Simple Circuit Building Practice - Worksheet 5A PPT
View & Print
  Simple Circuit Building Practice - Worksheet 5B PPT
View & Print
  Simple Circuit Building Practice - Worksheet 6 View & Print
 
  Optional Lab - Build Electrical Trainer - Lab See Instructor for kit

Module 4

A6 - Starting & Charging Systems
 
Starting & Charging Systems Videos
  Battery Power Video 1
Download VLC
Media Player
Battery Chemistry Video 2
Battery Energy Source Video 3
Alternator Principles Video 4
Alternator Construction Video 5
Starter Motor Principles Video 6
Starter Motor Construction Video 7
 
Starting & Charging Systems Skills Diagnostic Skills
  SC1 – Skill -- Checking State-of-Charge Video
PPT
Print Task
 
SC2 – Skill -- Charging a Battery PPT
Print Task
 
SC3A – Skill -- Starting a Vehicle with a Battery Booster Video
Print Task
 
SC4A – Skill -- Battery Conductance Test Battery Catalog
Video
PPT
Print Task
 
SC6 – Skill -- Alternator Output Test Video
PPT
Print Task
 
SC8 – Skill -- Starter Draw Test PPT
Print Task
 
SC10 – Skill -- Parasitic Draw Test (w/ test lamp) PPT
Print Task
 

SC11 – Skill -- Complete Starting-Charging System Diagnosis

(Putting SC1, SC4A, SC6, SC8, and SC10 together)

Mastery Skill
Print Task
 
Starting & Charging Systems On-line Assignment Theory
  Chapter 32 - Charging System Technology PPT
Worksheet
Quiz
Chapter 33 - Charging System Diagnosis, Testing, and Repair PPT
Worksheet
 
Starting & Charging Systems Skills Repair Skills
   
SC5 – Skill -- Remove and Install Battery Video 1 - Remove
Video 2 - Install
Print Task
 
OPTIONAL DIAGNOSTIC & REPAIR SKILLS
  SC3B – Skill -- Starting a Vehicle with Jumper Cables PPT
Print TaskB
 
SC4B – Skill -- Battery Load Test PPT
Print Task
 
SC10B – Skill -- Parasitic Draw Test (w/ Ammeter) Video
Print Task
 
Starting-Charging Timed Hands-on Assessment Print Task
 
SC7 – Skill (Optional, if time allows) R&I Alternator Print Task
 
SC9 – Skill (Optional, if time allows) R&I Starter Print Task
 
Module 5
NATEF Electrical Labs
  Electrical System Labs All-Data Pro
  A6 A- General Electrical System Diagnosis

Labs

  A1 Complete work order to include customer information,
Vehicle identifying information, customer concern, related
service history, cause, and correction.
P-1 LAB
  A2 Identify and interpret electrical/electronic system concern; determine necessary action. (Do this in conjunction with A13) P-1

LAB

  A13 Inspect and test fusible links, circuit breakers, and fuses; determine necessary action. (Do this in conjunction with A2) P-1

LAB

  A3 Research applicable vehicle and service information, such as electrical/electronic system operation, vehicle service history, service precautions, and technical service bulletins. P-1 VIN Guide
  A4 Locate and interpret vehicle and major component identification numbers. LAB
  A5 Diagnose electrical/electronic integrity of series, parallel and series-parallel circuits using principles of electricity (Ohm’s Law). P-1 LAB
  A6 Use wiring diagrams during diagnosis of electrical circuit problems. P-1
  A7 Demonstrate the proper use of a digital multimeter (DMM) during diagnosis of electrical circuit problems, including: source voltage, voltage drop, current flow, and resistance. P-1 Covered in
Simple Circuits 1
  A8 Check electrical circuits with a test light; determine necessary action. P-2 Using a Test Light
PPT
LAB
  A9 Check electrical/electronic circuit waveforms; interpret readings and determine needed repairs. P-2 LAB
  A10 Check electrical circuits using fused jumper wires; determine necessary action. P-2 LAB
  A11 Locate shorts, grounds, opens, and resistance problems in electrical/electronic circuits; determine necessary action. P-1 LAB
  A12 Measure and diagnose the cause(s) of excessive parasitic draw; determine necessary action. P-1 LAB
  A14 Inspect and test switches, connectors, relays, solenoid solid state devices, and wires of electrical/electronic circuits; perform necessary action. P-1 LAB
  A15 Remove and replace terminal end from connector; replace connectors and terminal ends. P-1 LAB
  A16 Repair wiring harness (including CAN/BUS systems). P-1
  A17 Perform solder repair of electrical wiring. P-1 LAB
  A18 Identify location of hybrid vehicle high voltage circuit disconnect (service plug) location and safety procedures. P-2 LAB
Module 6
Lighting, Instrumentation, Wipers, and Horns
  Chapter 37 Lighting, Instrumentation, Wipers, and Horns PPT
View
Quiz
 
  Lighting and Instrumentation Videos      
  Lighting System Video 1
Download VLC
Media Player
  Stoplights Video 2
  Headlamps Video 3
  HID Headlamps Video 4
  Gages Video 5
  Temperature Indicators Video 6
 
  Lighting Systems Labs      
  A6 E - Lighting Systems Diagnosis and Repair      
  E1 Diagnose the cause of brighter than normal, intermittent, dim, or no light operation; determine necessary action. P-1   LAB
  E2 Inspect, replace, and aim headlights and bulbs. P-2   LAB
  E3 Inspect and diagnose incorrect turn signal or hazard light operation; perform necessary action. P-2   LAB
  E4 Identify system voltage and safety precautions associated with high intensity discharge headlights. P-2   LAB
Module 6
Gauges, Warning Systems
  Gauges, Warning System Labs   All-Data Pro
  A6 F- Gauges, Warning Devices, and Driver Information Systems Diagnosis and Repair      
  F1 Inspect and test gauges and gauge sending units for cause of abnormal gauge readings; determine necessary action. P-1   LAB
  F2 Inspect and test connectors, wires, and printed circuit boards of gauge circuits; determine necessary action. P-3   LAB
  F3 Diagnose the cause of incorrect operation of warning devices and other driver information systems; determine necessary action. P-1   LAB
  F4 Inspect and test sensors, connectors, and wires of electronic (digital) instrument circuits; determine necessary action. P-3   LAB
Module 7
  Horn and Wiper/Washer Labs      
  A6 G- Horn and Wiper/Washer Diagnosis and Repair      
  G1 Diagnose incorrect horn operation; perform necessary action. P-1   LAB
  G2 Diagnose incorrect wiper operation; diagnose wiper speed control and park problems; perform necessary action. P-1   LAB
  G3 Diagnose incorrect washer operation; perform necessary action. P-2   LAB
Module 8
  Sound Systems, and Power Accessories
On-Line Assignments - Chapter 38
    Quiz
  Chapter 38 Sound Systems, and Power Accessories PPT View Quiz
Module 9
  Accessories Videos      
  Remote Key System Video 1
  Optical Type Sensors Video 2
 
  Accessories Labs   All-Data Pro
  A6 H- Accessories Diagnosis and Repair      
  H1 Diagnose incorrect operation of motor-driven accessory circuits; determine necessary action. P-1   LAB
  H2 Diagnose incorrect heated glass, mirror, or seat operation; determine necessary action. P-3   LAB
  H3 Diagnose incorrect electric lock operation (including remote keyless entry); determine necessary action. P-1   LAB
  H4 Diagnose incorrect operation of cruise control systems; determine necessary action. P-3 LAB
  H5 Diagnose supplemental restraint system (SRS) concerns; determine necessary action. P-1
  H6 Disarm and enable the airbag system for vehicle service. P-1   LAB
  H7 Diagnose radio static and weak, intermittent, or no radio reception; determine necessary action. P-3   LAB
  H8 Remove and reinstall door panel. P-1   LAB
  H9 Diagnose body electronic system circuits using a scan tool; determine necessary action. P-2   LAB
  H10 Check for module communication (including CAN/BUS systems) errors using a scan tool. P-2   LAB
  H11 Diagnose the cause of false, intermittent, or no operation of anti-theft systems. P-3   LAB
  H12 Describe the operation of keyless entry/remote-start systems. P-3   LAB
  H13 Perform software transfers, software updates, or flash reprogramming on electronic modules. P-3   LAB
AST1B Final
 
Electrical/Electronic Systems Task Priority Breakdown
P‐1 = 39 _____No. Completed (95% ‐ 37 Required for NATEF)
P‐2 = 13 _____No. Completed (80% ‐ 9 Required for NATEF)
P‐3 = 10 _____No. Completed (50% ‐ 5 Required for NATEF)